OSCOR INC. SAFESHEATH ULTRA LITE; INTRODUCER, CATHETER, PRODUCT CODE: DYB, PRODUCT CODE: DYB
|
Back to Search Results |
|
Model Number V17 |
Device Problem
Material Too Rigid or Stiff (1544)
|
Patient Problem
No Clinical Signs, Symptoms or Conditions (4582)
|
Event Date 04/05/2021 |
Event Type
malfunction
|
Manufacturer Narrative
|
Conclusion not yet available, evaluation in process.A follow-up report will be submitted as soon as the investigation is complete.
|
|
Event Description
|
A nurse reported an issue with a 7f sterile valved introducer from a smartport procedure kit.During a procedure, the doctor was placing the port and the sheath did not peel like it was supposed to.One side (wing) broke off when the doctor attempted to peel it; therefore, the doctor had to grab it with forceps and rip it apart to remove it.The procedure was completed with this kit / device.There was no patient harm or injury due to the event.
|
|
Manufacturer Narrative
|
Correction h10: per ifu an-17-001z-x: first, withdraw the sheath from the vessel.Then remove the sheath by sharply snapping the tabs of the valve housing in a plane perpendicular to the long axis of the sheath to split the valve and peel the sheath apart.Oscor inc.Is submitting the above report to comply with 21 cfr part 803, the medical device reporting regulation.The report is based upon information obtained by oscor inc.Which the company may not have been able to investigate or verify prior to the date the report was required by fda.This report does not constitute an admission that the device, oscor inc., or its employees, caused or contributed to the event described in this report.Nor does this report reflect a conclusion by fda, oscor inc., or its employees, that the report constitutes an admission that the device, oscor inc., or its employees caused or contributed to the event described in this report.
|
|
Manufacturer Narrative
|
The device was used in treatment.The device was not returned for analysis, therefore, the exact cause of the product issue cannot be determined and the clinical observation could not be confirmed.However, the following controls are in place to mitigate the reported product issue.The device history records were reviewed to confirm that the device passed all applicable in-process and final inspections.Per procedure (adelante-s introducer sheath in process and final inspections): first 5 good shots (6-10) and 5 last shots): visual inspection: verify hub to be smooth, no cracks, sinking or unfilled areas, and check.Using 10x microscope, look down into hub for irregularities.Verify one of the score lines of the sheath is aligned with the break line of the hub (handle).Verify smooth transition between sheath and hub on inside of hub.With the naked eye, verify sheath is free of kinks, dirt and any other damages.Break and peel test: using samples from fit check, manually break the sheath and hub and verify that the seal splits easily without extreme elongation.Also verify that the split cap and seal remain secure and do not break free or loosen from the sheath hub.Manually peel the sheath and verify the sheath peels easily along the sheath body and tip.Per ifu: advance the dilator and sheath together with a twisting motion over the guide wire and into the vessel.Fluoroscopic observation may be advisable.Attaching a clamp or hemostat to the proximal end of the guide wire will prevent inadvertently advancing the guide wire entirely into the patient.Once assembly is fully introduced into the vascular system, separate the dilator cap from the sheath valve housing by rotating the dilator cap off the hub.Slowly retract the guide wire and dilator, leaving the sheath in position.The hemostasis valve will reduce the loss of blood and the inadvertent aspiration of air through the sheath.Introduce the catheter through the hemostasis valve/sheath and advance it into position.First, withdraw the sheath from the vessel.Then remove the sheath by sharply snapping the tabs of the valve housing in a plane perpendicular to the long axis of the sheath to split the valve and peel the sheath apart.Based on the investigation, a capa is not required as findings did not identify a design, labeling or manufacturing non-conformity.In addition, there was no new failure mode identified and the risk remains acceptable.The event will be re-evaluated if additional information becomes available.Oscor will continue to monitor this event type and risk.Oscor inc.Is submitting the above report to comply with 21 cfr part 803, the medical device reporting regulation.The report is based upon information obtained by oscor inc.Which the company may not have been able to investigate or verify prior to the date the report was required by fda.This report does not constitute an admission that the device, oscor inc., or its employees, caused or contributed to the event described in this report.Nor does this report reflect a conclusion by fda, oscor inc., or its employees, that the report constitutes an admission that the device, oscor inc., or its employees caused or contributed to the event described in this report.
|
|
Manufacturer Narrative
|
Correction: d1 brand name which should be safesheath® ultra lite.Oscor inc.Is submitting the above report to comply with 21 cfr part 803, the medical device reporting regulation.The report is based upon information obtained by oscor inc.Which the company may not have been able to investigate or verify prior to the date the report was required by fda.This report does not constitute an admission that the device, oscor inc., or its employees, caused or contributed to the event described in this report.Nor does this report reflect a conclusion by fda, oscor inc., or its employees, that the report constitutes an admission that the device, oscor inc., or its employees caused or contributed to the event described in this report.
|
|
Search Alerts/Recalls
|
|
|