MEDOS INTERNATIONAL SARL TRUESPAN MENISCAL REPAIR SYSTEM PLGA 12 DEGREE; SOFT-TISSUE ANCHOR, BIOABSORBABLE
|
Back to Search Results |
|
Model Number 228161 |
Device Problem
Material Deformation (2976)
|
Patient Problem
No Clinical Signs, Symptoms or Conditions (4582)
|
Event Date 09/13/2022 |
Event Type
malfunction
|
Event Description
|
It was reported by the sales rep that during an unknown procedure on (b)(6) 2022, it was observed that the end of the needle on the truespan meniscal repair system plga 12 degree device was shredded.Another like device was used to complete the procedure.There were no adverse patient consequences nor surgical delay reported.No additional information was provided.
|
|
Manufacturer Narrative
|
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by depuy mitek or its employees that the report constitutes an admission that the device, depuy mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Udi: (b)(4).Reporter is a j&j sales representative.To date the device has not been returned.If the device or further details are received at a later date a supplemental medwatch will be sent.
|
|
Manufacturer Narrative
|
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by depuy mitek or its employees that the report constitutes an admission that the device, depuy mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Investigation summary: the product was returned to mitek for evaluation.Mitek then conducted visual inspection of device receive.Upon visual inspection of the device revealed that only one implant was received attached in the suture.The other implant appears to have been removed from the suture.The orthocord suture tips were frayed which it is a sign of breakage.The truespan comes in normal use condition, no broken parts or any deficiencies could be observed in the needle and the entire gun.When performing the functional test, the red trigger was fully squeezed several times, it performed as intended.Manufacturing record evaluation is not required as the reported event is not associated with the manufacturing process and/or the potential cause of the defect cannot be associated to manufacturing.According with needle condition, this complaint cannot be confirmed and the root cause for the issue experienced by the customer cannot be established.A possible root cause for the condition of the needle can be attributed to a sharp instrument rubbed the suture and an excessive force applied to the suture at the moment of tightening the repair.The needle could be damage when it was inside the joint and the needle tip was maneuver to desired location for optimal approximation, it was leveraged, therefore causing stress and a mechanical deformation which can caused to breaking.As per ifu, it is important to use caution when tensioning the suture.Overtensioning may cause tissue damage and/or suture or implant breakage.Also, when penetrate the tissue to desired depth, again referencing the laser line at 10 mm on the needle as a secondary depth indicator as needed.Avoid damaging suture with needle.Finally, for the needle insertion, it is necessary use a calibrated probe, measure the width of the meniscal tissue to help insert into the joint.Set the adjustable depth stop to minimize tissue penetration depth.Also, during needle insertion use a malleable graft retractor or slotted cannula to prevent the needle from catching on or damaging tissue.At this point in time, no corrective action is required, and no further action is warranted.However, in depuy synthes mitek, additional complaint information monitoring for potential safety signals is conducted through complaint trending as part of post market surveillance.
|
|
Manufacturer Narrative
|
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by depuy mitek or its employees that the report constitutes an admission that the device, depuy mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.H10 additional narrative: d9, h3, h6: the actual device has been returned and is currently pending evaluation.Once reliability engineering evaluates the device, a supplemental medwatch report will be sent accordingly.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.
|
|
Search Alerts/Recalls
|
|
|