OBERDORF SYNTHES PRODUKTIONS GMBH CANN SCREW MEASURING DEVICE FOR 6.5MM & 7.3MM CANN SCREWS; GAUGE,DEPTH
|
Back to Search Results |
|
Catalog Number 319.700 |
Device Problem
Output Problem (3005)
|
Patient Problem
No Consequences Or Impact To Patient (2199)
|
Event Type
malfunction
|
Manufacturer Narrative
|
Complainant part is expected to be returned for manufacturer review/investigation, but has yet to be received.The investigation could not be completed; no conclusion could be drawn, as no product was received.Based on the information available, it has been determined that no corrective and/or preventative action is proposed.This complaint will be accounted for and monitored via post market surveillance activities.If additional information is made available, the investigation will be updated as applicable.A review of the device history records has been requested.Device was used for treatment, not diagnosis.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.
|
|
Event Description
|
Device report from synthes europe reports an event in (b)(6) as follows: it was reported that during an unknown surgical procedure on an unknown date, two (2) depth gauges did not function properly.When surgeon used each of them with a guide wire to measure the depth of a screw hole, the devices each gave different measurements.A third device was used to check the measurement.One of the complained devices measured the same as the third device while the other measured differently.The measurements differed by about 5 millimeters.Surgeon suspected the difference is due to either wear or breakage of the device.Surgery was completed successfully with no delay and no adverse consequence to the patient.Patient status reported as stable.Concomitant devices: guide wire (part unknown, lot unknown, quantity 1), depth gauge (part unknown, lot unknown, quantity 1).This report is for one (1) depth gauge.This is report 1 of 2 for (b)(4).
|
|
Manufacturer Narrative
|
Depuy synthes is submitting this report pursuant to the provisions of 21 cfr, part 803.This report may be based on information which depuy synthes has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by fda, depuy synthes or its employees that the report constitutes an admission that the device, depuy synthes, or its employees caused or contributed to the potential event described in this report.If the information is unknown, not available or does not apply, the section/field of the form is left blank.Investigation summary: the device was not received for investigation but a pd investigation using the received photos and event information was conducted.With the attached photos with no lot number, we are not able to define the investigation report.We also are not able to make any statement on the condition.It is visible that the oxide layer is partially removed but this has no influence on measuring result.Product was not returned.Based on the information available, it has been determined that no corrective and/or preventative action is proposed.This complaint will be accounted for and monitored via post market surveillance activities.If additional information is made available, the investigation will be updated as applicable.Device was used for treatment, not diagnosis.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.
|
|
Manufacturer Narrative
|
Depuy synthes is submitting this report pursuant to the provisions of 21 cfr, part 803.This report may be based on information which depuy synthes has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by fda, depuy synthes or its employees that the report constitutes an admission that the device, depuy synthes, or its employees caused or contributed to the potential event described in this report.Described product problem was forwarded to sustaining engineering for evaluation: direct measuring device 319.70 and 319.700 are of a different design and can only be used with the corresponding surgical technique and screw racks.Based on the registration of the devices 319.70 should only be available in us and canada.The reason why the surgeon had both devices available does not form part of this investigation.Based on the investigation findings, it has been determined that no corrective and/or preventative action is proposed.Device history lot, part: 319.700 , lot: 8613392, manufacturing site: haegendorf, release to warehouse date: 05.Nov.2013.The device history record shows this lot was processed through the normal manufacturing and inspection operations with no rework or nonconformities noted.This lot met all dimensional and visual criteria at the time of release with no issues documented during the manufacturing process.Device history review - review of the device history record showed that there were no issues during the manufacture of this product which would contribute to this complaint condition device was used for treatment, not diagnosis.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.
|
|
Search Alerts/Recalls
|
|
|