• Decrease font size
  • Return font size to normal
  • Increase font size
U.S. Department of Health and Human Services

MAUDE Adverse Event Report: THORATEC SWITZERLAND GMBH CENTRIMAG 2ND GENERATION PRIMARY CONSOLE; CONTROL, PUMP SPEED, CARDIOPULMONARY BYPASS

  • Print
  • Share
  • E-mail
-
Super Search Devices@FDA
510(k) | DeNovo | Registration & Listing | Adverse Events | Recalls | PMA | HDE | Classification | Standards
CFR Title 21 | Radiation-Emitting Products | X-Ray Assembler | Medsun Reports | CLIA | TPLC
 

THORATEC SWITZERLAND GMBH CENTRIMAG 2ND GENERATION PRIMARY CONSOLE; CONTROL, PUMP SPEED, CARDIOPULMONARY BYPASS Back to Search Results
Model Number 201-30300
Device Problem Infusion or Flow Problem (2964)
Patient Problem No Clinical Signs, Symptoms or Conditions (4582)
Event Date 08/19/2022
Event Type  malfunction  
Manufacturer Narrative
No further information was provided.A supplemental report will be submitted when the manufacturer¿s investigation is completed.
 
Event Description
It was reported that the patient was in the intensive care unit (icu) with extracorporeal membrane oxygenation (ecmo).The patient presented hemodynamic decompensation that required inotropic support, the patient recovered without problem.The patient presented loss of flows on three occasions.The console did not register the flow.The decision was made to change the console and backup flow probe and the flow was normalized.The engine was not changed.There were no consequences for the patient.The patient was stable.Manufacturer report number of flow probe: 3003306248-2022-12510.
 
Manufacturer Narrative
Section d4: expiration date provide in previous report is not applicable.Manufacturer's investigation conclusion: the reported event of flow alarms was able to be confirmed via review of the log files.The centrimag 2nd generation primary console (serial number: l05115-0010) was returned for evaluation and a log file was downloaded for review.A review of the downloaded log files showed events spanning approximately 6 days (12aug2022, 15aug2022 ¿ 19aug2022, 09jan2023 per timestamp).Events captured on 09jan2023 took place in the testing labs at abbott.Atypical flow signal interrupted: f2 alarms were intermittently active upon startup on 18aug2022 between 19:42 ¿ 19:52.The flow suddenly dropped on 18aug2022 at 20:50 from ~1.8 lpm to ~0 lpm with no alarms active and recovered to ~1 lpm at 21:00 while the pump speed remained stable.The flow dropped suddenly to ~0 lpm and showed negative values triggering flow below minimum: f3 and flow signal interrupted: f2 alarms to intermittently activate on 12aug2022 between 04:33 - 04:37, on 18aug2022 between 21:43 ¿ 21:44, at 22:33, from 22:44 ¿ 22:47, on 19aug2022 at 00:37, intermittently from 01:07 ¿ 01:12, at 04:19, and from 04:27 ¿ 04:28.The alarms were able to be muted and cleared shortly after activating when the flow was able to be recorded above the minimum flow value.The system was shut down on 19aug2022 at 05:14.There were no other notable alarms active in the log file.The centrimag 2nd generation primary console was returned for analysis to the service depot along with the flow probe.The console and flow probe were connected to a test loop with no alarms active.The console underwent functional testing and passed.The alarms were unable to be reproduced during testing.The root cause of the reported event was unable to be conclusively determined through this investigation.The device history records were reviewed for the centrimag 2nd generation primary console (serial number: l05115-0010) and was found to pass all manufacturing and quality assurance specifications.The 2nd generation centrimag system operating manual section 4 entitled "warnings & precautions" warns "one additional 2nd generation centrimag primary console, motor and flow probe are required as backup system in the immediate vicinity of each patient whenever the centrimag or pedivas blood pump is used.The backup console must be connected to the backup motor and to the backup flow probe, have a battery charge sufficient for at least one hour of operation, be connected to ac power (except during transport) and be immediately available should the main console, motor or flow probe experience a malfunction." the 2nd generation centrimag system operating manual section 10 entitled "emergency and troubleshooting" states that "the recommended practice whenever there is a 2nd generation centrimag primary console or motor malfunction is to replace the console and motor as a set.Remove the blood pump from the malfunctioning motor and console and place the blood pump in the backup motor and console to continue patient support.Do not exchange individual motors or individual consoles during patient support." the 2nd generation centrimag system operating manual table 16 entitled ¿console alarms & alerts¿ addresses how to interpret and troubleshoot all system alarms including f2 and f3 alarms.No further information was provided.The manufacturer is closing the file on this event.
 
Search Alerts/Recalls

  New Search  |  Submit an Adverse Event Report

Brand Name
CENTRIMAG 2ND GENERATION PRIMARY CONSOLE
Type of Device
CONTROL, PUMP SPEED, CARDIOPULMONARY BYPASS
Manufacturer (Section D)
THORATEC SWITZERLAND GMBH
technoparkstrasse 1
zurich CH-80 05
SZ  CH-8005
Manufacturer (Section G)
THORATEC SWITZERLAND GMBH
technoparkstrasse 1
zurich CH-80 05
SZ   CH-8005
Manufacturer Contact
bob fryc
6035 stoneridge drive
pleasanton, CA 94588
7818528204
MDR Report Key15434305
MDR Text Key300786411
Report Number3003306248-2022-12509
Device Sequence Number1
Product Code DWA
Combination Product (y/n)N
Reporter Country CodeCO
PMA/PMN Number
K131179
Number of Events Reported1
Summary Report (Y/N)N
Report Source Manufacturer
Source Type Foreign,Health Professional,Company Representative
Reporter Occupation Other Health Care Professional
Type of Report Initial,Followup
Report Date 01/27/2023
1 Device was Involved in the Event
1 Patient was Involved in the Event
Date FDA Received09/15/2022
Is this an Adverse Event Report? No
Is this a Product Problem Report? Yes
Device Operator Lay User/Patient
Device Model Number201-30300
Device Lot NumberL05115
Was Device Available for Evaluation? Device Returned to Manufacturer
Is the Reporter a Health Professional? Yes
Was the Report Sent to FDA? No
Date Manufacturer Received01/26/2023
Was Device Evaluated by Manufacturer? Yes
Date Device Manufactured01/13/2017
Is the Device Single Use? No
Is This a Reprocessed and Reused Single-Use Device? No
Type of Device Usage Reuse
Patient Sequence Number1
-
-