• Decrease font size
  • Return font size to normal
  • Increase font size
U.S. Department of Health and Human Services

MAUDE Adverse Event Report: CARDINAL HEALTH SANTA CLARA MYNX CONTROL; DEVICE, HEMOSTASIS, VASCULAR

  • Print
  • Share
  • E-mail
-
Super Search Devices@FDA
510(k) | DeNovo | Registration & Listing | Adverse Events | Recalls | PMA | HDE | Classification | Standards
CFR Title 21 | Radiation-Emitting Products | X-Ray Assembler | Medsun Reports | CLIA | TPLC
 

CARDINAL HEALTH SANTA CLARA MYNX CONTROL; DEVICE, HEMOSTASIS, VASCULAR Back to Search Results
Catalog Number MX6760E
Device Problems Decrease in Pressure (1490); Material Rupture (1546)
Patient Problem No Clinical Signs, Symptoms or Conditions (4582)
Event Date 02/08/2024
Event Type  malfunction  
Event Description
As reported, the balloon of a 6/7f mynx control vascular closure device (vcd) burst during prep.Therefore, the product wasn¿t available and manual compression was performed for 20 minutes and the patient recovered.There was no reported patient injury.The device was used in a transfemoral cerebral angioplasty (tfca) procedure.The device was opened in a sterile field.A 6f non-cordis sheath was used.The device was prepared and used in accordance with the instructions for use (ifu).There were no visible signs of device/package damage prior to use.The physician achieved certification on the use of mynx and has used the device several times prior to this procedure.The device will be returned for evaluation.
 
Manufacturer Narrative
Additional information is pending and will be submitted within 30 days upon receipt.
 
Manufacturer Narrative
After further review of additional information received the following sections have been updated accordingly: d9, g3, g6, h1, h2, h3 this device is available for analysis but the engineering report is not yet available.However, it will be submitted within 30 days upon receipt.Additional information is pending and will be submitted within 30 days upon receipt.
 
Manufacturer Narrative
After further review of additional information received the following sections have been updated accordingly: g3, g6, h1, h2, h3 and h6.As reported, the balloon of a 6f/7f mynx control vascular closure device (vcd) burst during prep.Therefore, the product wasn¿t available and manual compression was performed for 20 minutes and the patient recovered.There was no reported patient injury.The device was used in a transfemoral cerebral angioplasty (tfca) procedure.The device was opened in a sterile field.A 6f non-cordis sheath was used.The device was prepared and used in accordance with the instructions for use (ifu).There were no visible signs of device/package damage prior to use.The physician achieved certification on the use of mynx and has used the device several times prior to this procedure.A non-sterile ¿mynx control vcd 6f/7f¿ involved in the reported complaint was returned for investigation.Visual inspection of the received device showed that button 1 and button 2 were not depressed.The syringe and procedural sheath were not received for evaluation.The stopcock was observed opened, and the balloon was found fully deflated.In addition, the sealant was found in its manufactured position, fully covered by the sealant sleeves, and the sealant was not exposed to blood.In addition, no damages were observed to sealant sleeves assembly.Per functional analysis, the inflation/deflation test was conducted per the mynx control ifu.The findings indicated a balloon leak in the balloon of the returned device.Per microscopic analysis, upon visual inspection at high magnification, a longitudinal tear was discovered in the balloon of the returned device.The reported event of ¿balloon-balloon loss of pressure¿ was confirmed through analysis of the returned device.However, the exact cause of the longitudinal tear condition found could not be conclusively determined during analysis.Based on the limited information available for review and product analysis, it is not possible to determine what factors may have contributed to the issue reported.However, as this issue was found during preparation of the device, handling factors during prep are possible.According to the ifu during the prepare balloon step, which is not intended as a mitigation, ¿fill locking syringe with 2 to 3 ml of sterile saline, attach to stopcock and draw vacuum.Check luer connector and tighten if necessary.Inflate the balloon until the black marker on the inflation indicator is fully visible.Check for leaks in the balloon and syringe connector; retighten if necessary.Discard the device if the balloon does not maintain pressure.Check for air bubbles in the balloon.If air bubbles are visible, deflate the balloon, draw vacuum to remove bubbles and re-inflate.¿ neither the product analysis, nor the information available for review suggest that the reported failure could be related to the design or manufacturing process of the unit.Therefore, no corrective/preventative actions will be taken at this time.
 
Search Alerts/Recalls

  New Search  |  Submit an Adverse Event Report

Brand Name
MYNX CONTROL
Type of Device
DEVICE, HEMOSTASIS, VASCULAR
Manufacturer (Section D)
CARDINAL HEALTH SANTA CLARA
5452 betsy ross drive
santa clara CA 95054
Manufacturer (Section G)
CORDIS US CORP.
14201 nw 60 avenue
miami lakes FL 33014
Manufacturer Contact
karla castro
5452 betsy ross drive
santa clara, CA 95054
7863138372
MDR Report Key18966562
MDR Text Key338750621
Report Number3004939290-2024-00139
Device Sequence Number1
Product Code MGB
Combination Product (y/n)N
Reporter Country CodeUS
PMA/PMN Number
P040044
Number of Events Reported1
Summary Report (Y/N)N
Report Source Manufacturer
Source Type Foreign,Health Professional,Company Representative
Reporter Occupation Other Health Care Professional
Type of Report Initial,Followup
Report Date 04/18/2024
1 Device was Involved in the Event
1 Patient was Involved in the Event
Date FDA Received03/24/2024
Is this an Adverse Event Report? No
Is this a Product Problem Report? Yes
Device Operator Health Professional
Device Catalogue NumberMX6760E
Device Lot NumberF2329103
Was Device Available for Evaluation? Device Returned to Manufacturer
Is the Reporter a Health Professional? Yes
Was the Report Sent to FDA? No
Date Manufacturer Received03/25/2024
Was Device Evaluated by Manufacturer? No
Date Device Manufactured11/01/2023
Is the Device Single Use? Yes
Is This a Reprocessed and Reused Single-Use Device? No
Type of Device Usage Initial
Patient Sequence Number1
Treatment
6F TERUMO SHEATH.
-
-