Catalog Number LSM1350626 |
Device Problem
Difficult to Advance (2920)
|
Patient Problem
No Known Impact Or Consequence To Patient (2692)
|
Event Date 08/18/2017 |
Event Type
malfunction
|
Manufacturer Narrative
|
The information provided by bard represents all of the known information at this time.Despite good faith efforts to obtain additional information, the complainant / reporter was unable or unwilling to provide any further patient, product, or procedural details to bard.Receipt of device is not expected.The investigation is currently in progress.Not returned.
|
|
Event Description
|
It was reported that the device was tight going through the 6f introducer sheath.The device was tight going through the 6f brite tip introducer sheath.The healthcare professional has used v12 before and has had no issues using 6f previously.There was no reported patient injury.
|
|
Manufacturer Narrative
|
It was reported that the device was tight going through the 6f introducer sheath.There were no anomalies noted during the prep of the device.There was no damage noted to the box, tray or stent cover and there was no difficulty removing the stent cover.The target lesion is unknown.The patient was being treated for an occlusion.A contralateral approach was made.The access location was the groin.The device was inserted into the sheath.Resistance was felt when advancing through the 6f brite tip introducer sheath.The device was tight when being advanced through the 6f sheath and force was used to push the device through.The procedure was completed using this device and sheath and the stent was implanted at the target lesion.Air evacuation was performed prior to inserting the device into the sheath.Multiple attempts were required to insert the device into the sheath.The device was not removed back through the sheath at any time during the procedure.Guidewire access was maintained throughout the procedure.The healthcare professional has used v12 before and has had no issues using 6f previously.There was no reported patient injury.The lot history records have been reviewed with special attention to the manufacturing and inspection of this product.The device was found to have met specifications prior to shipment.No manufacturing anomalies were identified that may have caused or contributed to the reported event.This is the first reported complaint for this lot number and issue to date.The device was not returned for evaluation.The result of the investigation is inconclusive as no sample was returned for evaluation.Based upon the available information and sample evaluation a definitive root cause has not been determined.It is unknown if patient factors, handling or procedural techniques may have contributed to the reported event.(b)(4).The ifu states: device description: implant: the lifestream¿ balloon expandable vascular covered stent is comprised of an electropolished balloon-expandable stent made from 316l stainless steel, encapsulated between two layers of eptfe.Indication for use: the lifestream¿ balloon expandable vascular covered stent is indicated for the treatment of atherosclerotic lesions in common and external iliac arteries.Directions for use: site access and preparation; using standard techniques access the artery and place an introducer sheath or guiding catheter of appropriate inner diameter and a 0.035" (0.89 mm) guidewire across the target lesion.Perform diagnostic angiography to confirm site of implantation and measure the reference vessel diameter and lesion length.Covered stent size selection: select a covered stent diameter that is approximately 5%-20% larger than the largest reference vessel diameter at the proximal or distal target site.Refer to the sizing table on the packaging label for appropriate selection of the covered stent diameter and length.Endovascular system preparation: carefully remove the selected device from the package.Inspect the covered stent for adherence to the balloon and centered placement in relation to the balloon marker bands.If the covered stent is not centered and/or does not firmly adhere to the balloon, do not use.Flush the delivery system guidewire lumen with sterile saline mixture until saline drops from the distal end of the endovascular system.Air evacuation: a 20 cc or smaller luer-lock syringe with a minimum of 5 cc¿s sterile saline mixture is recommended for use for aspirating this device.With the distal balloon tip pointing down and positioned below the level of the syringe, pull negative pressure until all air is expelled.Induce a negative pressure to remove any air from the balloon and inflation lumen.Repeat until all air is expelled.Carefully release to neutral.Allow the inflation lumen to fill with the diluted contrast medium and maintain a neutral pressure.Important: do not apply positive pressure to the balloon.Attach the prefilled inflation device to the inflation lumen of the catheter hub, ensuring no air bubbles remain at the catheter connection.Verify that the covered stent is still centered between the two radiopaque markers on the balloon catheter.Introduction of the endovascular system and placement of the covered stent advance the endovascular system over the guidewire into the introducer sheath.Further advance the endovascular system to the target treatment site within the introducer sheath and position the covered stent across the lesion.Verify that the covered stent is still centered within the balloon marker bands.Slowly retract the introducer sheath / guiding catheter while maintaining the position of the covered stent.Ensure the introducer sheath is retracted far enough to not compromise the balloon expansion and covered stent release.(b)(4).
|
|
Event Description
|
It was reported that the device was tight going through the 6f introducer sheath.There were no anomalies noted during the prep of the device.There was no damage noted to the box, tray or stent cover and there was no difficulty removing the stent cover.The target lesion is unknown.The patient was being treated for an occlusion.A contralateral approach was made.The access location was the groin.The device was inserted into the sheath.Resistance was felt when advancing through the 6f brite tip introducer sheath.The device was tight when being advanced through the 6f sheath and force was used to push the device through.The procedure was completed using this device and sheath and the stent was implanted at the target lesion.Air evacuation was performed prior to inserting the device into the sheath.Multiple attempts were required to insert the device into the sheath.The device was not removed back through the sheath at any time during the procedure.Guidewire access was maintained throughout the procedure.The healthcare professional has used v12 before and has had no issues using 6f previously.There was no reported patient injury.
|
|
Search Alerts/Recalls
|