MAUDE Adverse Event Report: C.R. BARD, INC. (COVINGTON) -1018233 BARD® INLAY OPTIMA® URETERAL STENT WITH NICORE¿ GUIDEWIRE; INLAY OPTIMA URETERAL STENT

Model Number 786624

Device Problems Partial Blockage (1065); Obstruction of Flow (2423)

Patient Problems No Consequences Or Impact To Patient (2199); No Known Impact Or Consequence To Patient (2692)

Event Date 11/27/2019

Event Type  malfunction  

Manufacturer Narrative

The investigation is still in progress.Once the investigation is complete, a supplemental report will be filed.The device was not returned.

Event Description

It was reported that the ureteral stent developed severe occlusions.

Manufacturer Narrative

The reported event was inconclusive as no sample was returned for evaluation.A potential root cause of the reported event could be poor punch condition of the drainage holes due to which the holes did not allow drainage, resulting in severe occlusions.The device history record was reviewed and found nothing that could have caused or contributed to the reported event.The instructions for use were found adequate and state the following: "precautions: ¿ suture may be cut off prior to stent placement.Remove suture if indwelling time is expected to be longer than 14 days.¿ avoid improper handling of stent such as bending, kinking, tearing, etc.Misuse could damage the overall integrity of the stent.¿ ureteral stents should be checked periodically for signs of encrustation and proper function.Periodic checks of the stent by cystoscopic and/or radiographic procedures are recommended at intervals deemed to be appropriate by the physician in consideration of the individual patient¿s condition and other patient specific factors.When long-term use is indicated, it is recommended that indwelling time not exceed 365 days.The stent is not intended as a permanent indwelling device.* ¿ with any ureteral stent, migration is a possible complication, which could require medical intervention for removal.Selection of too short a stent may result in migration.¿ care should be exercised when removing the stent from the inner polybag to eliminate tearing or fragmentation.¿ the insertion of a ureteral stent should only be done by those individuals who have comprehensive training in the techniques and risks of the procedure.Multi-length ureteral stents: formation of knots in multi-length ureteral stents may occur.This may result in injury to the ureter during removal and/or the need for additional surgical intervention.The presence of a knot should be considered if significant resistance is encountered during attempts at removal.Potential complications: potential complications associated with retrograde/antegrade positioning of indwelling ureteral stents include the following: ¿ edema ¿ stone formation ¿ peritonitis ¿ extravasation ¿ ureteral reflux ¿ stent dislogdgement, ¿ fistula formation ¿ loss of renal function fragmentation, migration, occlusion ¿ hemorrhage ¿ pain/discomfort ¿ stent encrustation ¿ hydronephrosis ¿ perforation of kidney, renal ¿ ureteral erosion ¿ infection pelvis, ureter and/or bladder ¿ urinary symptoms directions for use: 1.Determine the proper stent length for the patient.This is generally calculated from the baseline pyelogram.Accurate measurements will optimize drainage efficiency and patient comfort.2.Insert the cystoscope then pass the guidewire* through the scope until the tip is in the renal pelvis.3.Move the pigtail straightener over the proximal end (kidney coil end) of the ureteral stent allowing easier insertion onto the guidewire.Remove pigtail straightener once the stent is secure on the guidewire.4.Pass the stent over the guidewire through the cystoscope by using the push catheter for proper placement.5.Watch the distal end (bladder coil end) of the stent or the radiopaque, proximal end of the pusher.Stop advancing when the stent¿s distal end marker reaches the ureterovesical junction (uvj).**(see below for proper placement directions on the multi-length ureteral stent.) 6.Withdraw the guidewire slowly.The stent will form a pigtail automatically.7.Carefully remove the push catheter.*activate the guidewire coating according to the ¿instructions for use¿ found within the guidewire packaging.**multi-length ureteral stent placement: to accurately size this stent count the marker bands as it is being advanced into the ureter.The first large band indicates the 22cm length.The second and third bands indicate 24cm and 26cm lengths respectively.The last large band is the 28cm length.If you need to place for the 30cm and 32cm lengths, use the attached suture or endoscopic forceps to gently pull back on the stent unwinding the coil from the kidney." h11:section a through f - the information provided by bd represents all of the known information at this time.Despite good faith efforts to obtain additional information, the complainant / reporter was unable or unwilling to provide any further patient, product, or procedural details to bd.H3 other text : the device was not returned.

Event Description

It was reported that the ureteral stent developed severe occlusions.

• Brand Name: BARD® INLAY OPTIMA® URETERAL STENT WITH NICORE¿ GUIDEWIRE
• Type of Device: INLAY OPTIMA URETERAL STENT
• Manufacturer (Section D): C.R. BARD, INC. (COVINGTON) -1018233; 8195 industrial blvd; covington GA 30014
• MDR Report Key: 9682112
• MDR Text Key: 183915333
• Report Number: 1018233-2020-00865
• Device Sequence Number: 1
• Product Code: FAD
• UDI-Device Identifier: 10801741015110
• UDI-Public: (01)10801741015110
• Combination Product (y/n): N
• PMA/PMN Number: K043193
• Number of Events Reported: 1
• Summary Report (Y/N): N
• Report Source: Manufacturer
• Source Type: company representative,other
• Type of Report: Initial,Followup
• Report Date: 03/17/2020

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Date FDA Received: 02/07/2020
• Is this an Adverse Event Report?: No
• Is this a Product Problem Report?: Yes
• Device Operator: Health Professional
• Device Expiration Date: 04/17/2022
• Device Model Number: 786624
• Device Catalogue Number: 786624
• Device Lot Number: NGBZ0178
• Was Device Available for Evaluation?: No
• Date Manufacturer Received: 03/12/2020
• Is This a Reprocessed and Reused Single-Use Device?: No
• Patient Sequence Number: 1