MAUDE Adverse Event Report: C.R. BARD, INC. (COVINGTON) -1018233 SL FOLEY SWIVEL SILICONE TRICOT 25BX; STATLOCK STABILIZATION DEVICE FOR FOLEY CATHETER

Catalog Number FOL0102

Device Problems Loss of or Failure to Bond (1068); Disconnection (1171)

Patient Problems No Consequences Or Impact To Patient (2199); No Known Impact Or Consequence To Patient (2692)

Event Date 04/02/2020

Event Type  malfunction  

Manufacturer Narrative

The investigation is still in progress.Once the investigation is complete a supplemental report will be filed.

Event Description

It was reported that the adhesive pad disconnected from the statlock device soon after placement.

Event Description

It was reported that the adhesive pad disconnected from the statlock device soon after placement.

Manufacturer Narrative

The reported event was confirmed.Visual inspection noted one foley statlock was received with the original packaging.Visual evaluation noted the swivel base was disconnected from the adhesive pad on return.This was a failure which stated that the assembly must be completely bonded.Although the reported event was confirmed, a root cause could not be determined.A potential root cause for this failure could be glue selection incompatible with clamp base.The device history record was reviewed and found nothing that could have caused or contributed to the reported event.The instructions for use were found adequate and state the following: ¿application technique prep 1.Place foley catheter into retainer.Directional arrow should point towards catheter tip, and balloon inflation arm should be next to the hinge.2.Close lid, being careful to avoid pinching the catheter.3.Identify securement site by laying the device retainer on the front of the thigh, leaving 2.5 cm of catheter slack between insertion site and the statlock® device retainer.4.After placing the statlock® stabilization device off to the side, cleanse and degrease the securement site with alcohol per hospital policy.Let skin dry.5.Apply skin protectant, in direction of hair growth, to area larger than securement site.Allow to dry completely (10-15 seconds).6.Using permanent marker, write initials and date of application on the statlock® device anchor pad.Note: always secure catheter into the statlock® device retainer before applying adhesive pad on skin.Place and peel 7.Align the statlock® stabilization device over securement site leaving 2.5 cm of catheter slack.Make sure leg is fully extended.8.While holding the retainer to keep the pad in place, peel away paper backing, one side at a time and place tension-free on skin.Removal technique disengage 1.Open retainer by pressing release button with thumb, then lift to open.2.Remove foley catheter from the statlock® device.Dissolve 3.Wipe the edge of the pad using at least 5-6 alcohol pads until a corner lifts.Then continue to stroke undersurface of pad with alcohol to dissolve adhesive pad away from skin.Do not pull or force pad to remove." h11:section a through f - the information provided by bd represents all of the known information at this time.Despite good faith efforts to obtain additional information, the complainant / reporter was unable or unwilling to provide any further patient, product, or procedural details to bd.

• Brand Name: SL FOLEY SWIVEL SILICONE TRICOT 25BX
• Type of Device: STATLOCK STABILIZATION DEVICE FOR FOLEY CATHETER
• Manufacturer (Section D): C.R. BARD, INC. (COVINGTON) -1018233; 8195 industrial blvd; covington GA 30014
• MDR Report Key: 9982520
• MDR Text Key: 188651087
• Report Number: 1018233-2020-02750
• Device Sequence Number: 1
• Product Code: EYJ
• Combination Product (y/n): N
• PMA/PMN Number: EXEMPT
• Number of Events Reported: 1
• Summary Report (Y/N): N
• Report Source: Manufacturer
• Source Type: distributor,other
• Type of Report: Initial,Followup
• Report Date: 05/27/2020

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Is this an Adverse Event Report?: No
• Is this a Product Problem Report?: Yes
• Device Operator: Health Professional
• Device Expiration Date: 04/28/2022
• Device Catalogue Number: FOL0102
• Device Lot Number: JUDSF373
• Was Device Available for Evaluation?: Device Returned to Manufacturer
• Date Returned to Manufacturer: 04/23/2020
• Initial Date Manufacturer Received: 04/03/2020
• Initial Date FDA Received: 04/21/2020
• Supplement Dates Manufacturer Received: 05/13/2020
• Supplement Dates FDA Received: 05/27/2020
• Is This a Reprocessed and Reused Single-Use Device?: No
• Patient Sequence Number: 1