MAUDE Adverse Event Report: C.R. BARD, INC. (COVINGTON) -1018233 SL FOLEY SWIVEL SILICONE 25BX; STATLOCK DEVICE

Model Number FOL0101

Device Problems Incorrect, Inadequate or Imprecise Result or Readings (1535); Insufficient Information (3190)

Patient Problems No Consequences Or Impact To Patient (2199); No Known Impact Or Consequence To Patient (2692)

Event Type  malfunction  

Manufacturer Narrative

The investigation is still in progress.Once the investigation is complete a supplemental report will be filed.

Event Description

It was reported that the foley statlocks had failed.

Event Description

It was reported that the foley statlocks had failed.

Manufacturer Narrative

The reported event was inconclusive due to the non-original product sample.Visual inspection noted that 2 unopened foley statlocks were received.Visual evaluation noted that no obvious defects were observed.The clamp door was properly secured to the base and the base was properly secured to the adhesive pad.An in house 16 fr foley catheter was inserted into the clamp.The clamp closed properly around the catheter, and the clamp door remained closed when the excessive force was applied to the catheter.This meets the specifications as the device functioning properly.A potential root cause for this failure mode could not be determined due to the lack of information.The product used for the treatment.It was unknown whether the device was related to the reported event.The device history record was reviewed and found nothing that could have caused or contributed to the reported event.The instructions for use were found adequate and state the following: "indications for use: the statlock® device is a stabilization device for compatible catheters.Contraindications: known tape or adhesive allergies.Warnings and precautions: 1.Do not use the statlock® device where loss of adherence could occur, such as with a confused patient, diaphoretic or non-adherent skin, or when the access device is not monitored daily.2.Observe universal blood and body fluid precautions and infection control procedures, during application and removal of the statlock® device.3.Minimize catheter manipulation during application and removal of the statlock® device.4.Daily maintenance: a.The statlock® device should be assessed daily and changed when clinically indicated, at least every seven days.B.If pad becomes soiled, wash with soap/water, saline or hydrogen peroxide.Do not use alcohol or prepackaged bathing systems, which could lead to early lifting.C.If showering/bathing, cover with plastic wrap or waterproof dressing.D.Conduct skin assessment prior to application and repeat daily per facility protocol.E.Use clinical judgment on the removal of the statlock® stabilization device if the patient experiences any fluid shifts that may interfere with skin integrity.Application technique prep 1.Place foley catheter into retainer.Directional arrow should point towards catheter tip, and balloon inflation arm should be next to the clamp hinge.2.Close lid, being careful to avoid pinching the catheter.3.Identify securement site by laying the device retainer on the front of the thigh, leaving 1 inch of catheter slack between insertion site and the statlock® device retainer.4.After placing the statlock® stabilization device off to the side, cleanse and degrease the securement site with alcohol per hospital policy.Let skin dry.5.Apply skin protectant, in direction of hair growth, to area larger than securement site.Allow to dry completely (10-15 seconds).6.Using permanent marker, write initials and date of application on the statlock® device anchor pad.Note: always secure catheter into the statlock® device retainer before applying adhesive pad on skin.Place and peel 7.Align the statlock® stabilization device over securement site leaving 1 inch of catheter slack.Make sure leg is fully extended.8.While holding the retainer to keep the pad in place, peel away paper backing, one side at a time and place tension-free on skin.Removal technique disengage 1.Open retainer by pressing release button with thumb, then lift to open.2.Remove foley catheter from the statlock® device.Dissolve 3.Wipe the edge of the pad using at least 5-6 alcohol pads until a corner lifts.Then continue to stroke undersurface of pad with alcohol to dissolve adhesive pad away from skin.Do not pull or force pad to remove.".

• Brand Name: SL FOLEY SWIVEL SILICONE 25BX
• Type of Device: STATLOCK DEVICE
• Manufacturer (Section D): C.R. BARD, INC. (COVINGTON) -1018233; 8195 industrial blvd; covington GA 30014
• MDR Report Key: 10437927
• MDR Text Key: 204693196
• Report Number: 1018233-2020-05362
• Device Sequence Number: 1
• Product Code: EYJ
• UDI-Device Identifier: 00801741076091
• UDI-Public: (01)00801741076091
• Combination Product (y/n): N
• PMA/PMN Number: EXEMPT
• Number of Events Reported: 1
• Summary Report (Y/N): N
• Report Source: Manufacturer
• Source Type: other,user facility
• Type of Report: Initial,Followup
• Report Date: 11/05/2020

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Date FDA Received: 08/21/2020
• Is this an Adverse Event Report?: No
• Is this a Product Problem Report?: Yes
• Device Operator: Health Professional
• Device Expiration Date: 02/28/2023
• Device Model Number: FOL0101
• Device Catalogue Number: FOL0101
• Device Lot Number: JUEP3729
• Was Device Available for Evaluation?: Device Returned to Manufacturer
• Date Returned to Manufacturer: 09/24/2020
• Date Manufacturer Received: 10/15/2020
• Is This a Reprocessed and Reused Single-Use Device?: No
• Patient Sequence Number: 1