|
Model Number EGIAADAPT |
Device Problems
Entrapment of Device (1212); Failure to Calibrate (2440); Misfire (2532); Human-Device Interface Problem (2949); Adverse Event Without Identified Device or Use Problem (2993)
|
Patient Problem
Unspecified Tissue Injury (4559)
|
Event Date 08/18/2022 |
Event Type
Injury
|
Event Description
|
According to the reporter, during a laparoscopic low anterior resection, in the middle of a rectal resection after finishing the detachment around the rectum, the device partially fired and the jaws could not be opened.The handle and battery were replaced, but the calibration did not go well.A manual adapter tool was used, but the jaws would still not not open and the knife did not return.It was also noted that the articulation part of cartridge was damaged and a component fell into the patient's cavity.The reload remained articulated, thus the reload could not be removed form the adapter and could not be removed from the trocar.The involved trocar was used without any malfunction.The surgeon converted the surgery into an open surgery, extended the incision for more than 1 inch, used forceps to clamp and take out the component and cut closer to the anus using a manual handle to remove the device.A circular stapling device was then used to complete the anastomosis.This led to tissue loss and over 30 minutes extended surgical time.
|
|
Manufacturer Narrative
|
Concomitant medical products: idrvultra1, idrvultra1 idrive ultra powered handle 1 (serial# (b)(4)); egia60amt, egia60amt egia 60 artic med thick sulu (lot#n1g0009y); intb100, intb100 idrive rechargeable batteryx1 (serial#unknown); unvca12stf, unvca12stf universal 12 stdfix cannula (serial#unknown).Medtronic is submitting this report to comply with fda reporting regulations under 21 cfr parts 4 and 803.This report is based upon information obtained by medtronic, which the company may not have been able to fully investigate or verify prior to the date the report was required by the fda.Medtronic has made reasonable efforts to obtain more complete information and has provided as much relevant information as is available to the company as of the submission date of this report.This report does not constitute an admission or a conclusion by fda, medtronic, or its employees that the device, medtronic, or its employee caused or contributed to the event described in the report.In particular, this report does not constitute an admission by anyone that the product described in this report has any ¿defects¿ or has ¿malfunctioned¿.These words are included in the fda 3500a form and are fixed items for selection created by the fda to categorize the type of event solely for the purpose of regulatory reporting.Medtronic objects to the use of these words and others like them because of the lack of definition and the connotations implied by these terms.This statement should be included with any information or report disclosed to the public under the freedom of information act.Any required fields that are unpopulated are blank because the information is currently unknown or unavailable.A good faith effort will be made to obtain the applicable information relevant to the report.If information is provided in the future, a supplemental report will be issued.
|
|
Manufacturer Narrative
|
D10 concomitant medical product/s: intb100, intb100 idrive rechargeable batteryx1 (serial#(b)(6) additional information: h3 evaluation summary: medtronic conducted an investigation based upon all information received.The device was available for evaluation.Visual inspection noted the black unload button was able to be pressed and the reload and cannula were removed.There was no damage to the tip of the firing rod.Functionally, the adapter was connected to a handle and the handle began the calibration sequence but generated a blue error light and a flashing adapter light.The adapter could not be calibrated, and a reload could not be loaded fully into the adapter.It was reported that the device initially fires but failed to complete the firing cycle, the device was difficult to unload, the device did not calibrate as expected, and the jaws of the device remain closed on tissue.The reported issues were confirmed.The most likely cause was not traced to the device.The manufacturing records for each device are thoroughly reviewed prior to release to ensure that it meets all medtronic quality specifications.Medtronic is submitting this report to comply with fda reporting regulations under 21 cfr parts 4 and 803.This report is based upon information obtained by medtronic, which the company may not have been able to fully investigate or verify prior to the date the report was required by the fda.Medtronic has made reasonable efforts to obtain more complete information and has provided as much relevant information as is available to the company as of the submission date of this report.This report does not constitute an admission or a conclusion by fda, medtronic, or its employees that the device, medtronic, or its employee caused or contributed to the event described in the report.In particular, this report does not constitute an admission by anyone that the product described in this report has any ¿defects¿ or has ¿malfunctioned¿.These words are included in the fda 3500a form and are fixed items for selection created by the fda to categorize the type of event solely for the purpose of regulatory reporting.Medtronic objects to the use of these words and others like them because of the lack of definition and the connotations implied by these terms.This statement should be included with any information or report disclosed to the public under the freedom of information act.Any required fields that are unpopulated are blank because the information is currently unknown or unavailable.A good faith effort will be made to obtain the applicable information relevant to the report.If information is provided in the future, a supplemental report will be issued.
|
|
Search Alerts/Recalls
|
|
|