MAUDE Adverse Event Report: C.R. BARD, INC. (COVINGTON) -1018233 CATHETER STABILIZATION DEVICE

Catalog Number FOL0105

Device Problem Loss of or Failure to Bond (1068)

Patient Problem No Clinical Signs, Symptoms or Conditions (4582)

Event Date 09/07/2023

Event Type  malfunction  

Event Description

It was reported that the statlock adhesive was not sticky enough.

Manufacturer Narrative

The reported event is inconclusive as no sample was returned for evaluation.A potential root cause for this failure could be ¿adhesive chemistry not appropriate for application (poor quick stick characteristics)".The lot number was unknown; therefore, the device history record could not be reviewed.The instructions for use were found adequate and state the following: ¿warnings and precautions: 1.Do not use the statlock® device where loss of adherence could occur, such as with a confused patient, diaphoretic or non-adherent skin, or when the access device is not monitored daily.Daily maintenance: a.The statlock® device should be assessed daily and changed when clinically indicated, at least every seven days.B.If pad becomes soiled, wash with soap/water, saline or hydrogen peroxide.Do not use alcohol or prepackaged bathing systems, which could lead to early lifting.C.If showering/bathing, cover with plastic wrap or waterproof dressing.D.Conduct skin assessment prior to application and repeat daily per facility protocol.Prep: 1.Place foley catheter into retainer.Directional arrow should point towards catheter tip, and balloon inflation arm should be next to the clamp hinge.2.Close lid, being careful to avoid pinching the catheter.3.Identify securement site by laying the device retainer on the front of the thigh, leaving 1 inch of catheter slack between insertion site and the statlock® device retainer.4.After placing the statlock® stabilization device off to the side, cleanse and degrease the securement site with alcohol per hospital policy.Let skin dry.5.Apply skin protectant, in direction of hair growth, to area larger than securement site.Allow to dry completely (10-15 seconds).6.Using permanent marker, write initials and date of application on the statlock® device anchor pad.Note: always secure catheter into the statlock® device retainer before applying adhesive pad on skin.Place and peel.7.Align the statlock® stabilization device over securement site leaving 1 inch of catheter slack.Make sure leg is fully extended.8.While holding the retainer to keep the pad in place, peel away paper backing, one side at a time and place tension-free on skin.The statlock® stabilization device should be monitored daily and replaced when clinically indicated, at least every 7 days.The catheter insertion site should be treated per local policy recommendations.The statlock® device is contraindicated on patients with known tape and adhesive allergies.Alcohol and acetone may weaken the adhesive bond between the statlock® device pad and the skin.Care should be taken when using these solutions while performing catheter site care.Please consult product inserts and labels for any indications, contraindications, hazards, warnings, cautions and directions for use.For additional information on the statlock® foley stabilization device, please call your local bard representative.¿ h11: section a through f - the information provided by bd represents all the known information at this time.Despite good faith efforts to obtain additional information, the complainant / reporter was unable or unwilling to provide any further patient, product, or procedural details to bd.H3 other text: the device was not returned.

• Brand Name: CATHETER STABILIZATION DEVICE
• Type of Device: CATHETER STABILIZATION DEVICE
• Manufacturer (Section D): C.R. BARD, INC. (COVINGTON) -1018233; 8195 industrial blvd; covington 30014
• Manufacturer (Section G): C.R. BARD, INC. (COVINGTON) -1018233; 8195 industrial blvd; covington 30014
• Manufacturer Contact: xeeroy rada ; 8195 industrial blvd; covington 30014 ; 7707846100
• MDR Report Key: 17894311
• MDR Text Key: 325388264
• Report Number: 1018233-2023-07238
• Device Sequence Number: 1
• Product Code: EYJ
• UDI-Device Identifier: 00801741076145
• UDI-Public: (01)00801741076145
• Combination Product (y/n): N
• Reporter Country Code: US
• PMA/PMN Number: EXEMPT
• Number of Events Reported: 1
• Summary Report (Y/N): N
• Report Source: Manufacturer
• Source Type: Other,Company Representative,Distributor
• Reporter Occupation: Other Health Care Professional
• Type of Report: Initial
• Report Date: 09/13/2023

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Date FDA Received: 10/09/2023
• Is this an Adverse Event Report?: No
• Is this a Product Problem Report?: Yes
• Device Operator: Lay User/Patient
• Device Catalogue Number: FOL0105
• Was Device Available for Evaluation?: No
• Is the Reporter a Health Professional?: Yes
• Date Manufacturer Received: 09/11/2023
• Was Device Evaluated by Manufacturer?: Device Not Returned to Manufacturer
• Is the Device Single Use?: Yes
• Is This a Reprocessed and Reused Single-Use Device?: No
• Type of Device Usage: Initial
• Patient Sequence Number: 1
• Patient Outcome(s): Other