MAUDE Adverse Event Report: C.R. BARD, INC. (COVINGTON) -1018233 SL FOLEY SWIVEL SILICONE 25BX; STATLOCK

Catalog Number FOL0100

Device Problems Disconnection (1171); Structural Problem (2506)

Patient Problems No Consequences Or Impact To Patient (2199); No Known Impact Or Consequence To Patient (2692)

Event Type  malfunction  

Manufacturer Narrative

The investigation is still in progress.Once the investigation is complete, a supplemental report will be filed.

Event Description

It was reported that the statlock will not stay closed around the 20fr.Silicone catheter.

Event Description

It was reported that the statlock will not stay closed around the 20fr.Silicone catheter.

Manufacturer Narrative

The reported event was unconfirmed.Visual inspection noted one used foley statlock with the original packaging was received.Visual evaluation noted one 16fr foley catheter was placed in the device and it was able to close properly.The foley catheter was pulled on below the clamp door with excessive force, and the clamp door remained closed.The device history record was reviewed and found nothing that could have caused or contributed to the reported event.The instructions for use were found adequate and state the following: ¿prep 1.Place foley catheter into retainer.Directional arrow should point towards catheter tip, and balloon inflation arm should be next to the clamp hinge.2.Close lid, being careful to avoid pinching the catheter.3.Identify securement site by laying the device retainer on the front of the thigh, leaving 1 inch of catheter slack between insertion site and the statlock® device retainer.4.After placing the statlock® stabilization device off to the side, cleanse and degrease the securement site with alcohol per hospital policy.Let skin dry.5.Apply skin protectant, in direction of hair growth, to area larger than securement site.Allow to dry completely (10-15 seconds).6.Using permanent marker, write initials and date of application on the statlock® device anchor pad.Note: always secure catheter into the statlock® device retainer before applying adhesive pad on skin.Place and peel 7.Align the statlock® stabilization device over securement site leaving 1 inch of catheter slack.Make sure leg is fully extended.8.While holding the retainer to keep the pad in place, peel away paper backing, one side at a time and place tension-free on skin.Removal technique disengage 1.Open retainer by pressing release button with thumb, then lift to open.2.Remove foley catheter from the statlock® device.Dissolve 3.Wipe the edge of the pad using at least 5-6 alcohol pads until a corner lifts.Then continue to stroke undersurface of pad with alcohol to dissolve adhesive pad away from skin.Do not pull or force pad to remove." h11:section a through f - the information provided by bd represents all of the known information at this time.Despite good faith efforts to obtain additional information, the complainant / reporter was unable or unwilling to provide any further patient, product, or procedural details to bd.

• Brand Name: SL FOLEY SWIVEL SILICONE 25BX
• Type of Device: STATLOCK
• Manufacturer (Section D): C.R. BARD, INC. (COVINGTON) -1018233; 8195 industrial blvd; covington GA 30014
• MDR Report Key: 8798717
• MDR Text Key: 151514236
• Report Number: 1018233-2019-03968
• Device Sequence Number: 1
• Product Code: EYJ
• UDI-Device Identifier: 00801741076077
• UDI-Public: (01)00801741076077
• Combination Product (y/n): N
• PMA/PMN Number: EXEMPT
• Number of Events Reported: 1
• Summary Report (Y/N): N
• Report Source: Manufacturer
• Source Type: consumer,other
• Type of Report: Initial,Followup
• Report Date: 09/04/2019

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Date FDA Received: 07/17/2019
• Is this an Adverse Event Report?: No
• Is this a Product Problem Report?: Yes
• Device Operator: Lay User/Patient
• Device Expiration Date: 06/28/2021
• Device Catalogue Number: FOL0100
• Device Lot Number: JUCUF556
• Was Device Available for Evaluation?: Device Returned to Manufacturer
• Date Returned to Manufacturer: 07/18/2019
• Date Manufacturer Received: 08/26/2019
• Is This a Reprocessed and Reused Single-Use Device?: No
• Patient Sequence Number: 1