|
Model Number 3155637 |
Device Problem
Vibration (1674)
|
Patient Problem
Bone Fracture(s) (1870)
|
Event Date 10/06/2020 |
Event Type
Injury
|
Manufacturer Narrative
|
There were 3 devices (2 burs and 1 handpiece) being used in this surgery, we are submitting 3 mdrs for the same event.List of products involved: drill 3055601 skeeter oto-tool, serial # (b)(4) bur 3155637 oto-flex.7mm carbide green, lot# 0219522877 bur 3155637 oto-flex.7mm carbide green, lot# 0219854403.This is same event as regulatory report #: 1045254-2020-00523.If information is provided in the future, a supplemental report will be issued.
|
|
Event Description
|
A health care provider reported via manufacturer representative that the event during stapedectomy caused a fracture in incus instead of a controlled drilling.Two burs were used in the case and both wobbled.The burs did not rotate properly - the tip oscillates or 'wobbles'.The fragment was recovered so there was no long-lasting harm to the patient however, the procedure did not go as planned.There was 20 minutes delay.
|
|
Event Description
|
Additional information received that the reported burs that wobbled were initial use, not reprocessed, and some wobbled right out of the package.The bur was locked into place correctly.Hcp was familiar with the handpieces as he had used them for over 15 years.He performed troubleshooting by using the burs in different handpieces, to see the result.Each of the burs wobbled in a second handpiece; however, it was found that there was variability on how much of a wobble was evident with each handpiece (either more wobble, or less).The drills have recently been swapped out for new ones.The facility determined that this was an issue with their handpieces and returned each of their devices.Since the new devices have been in use, there has been no evident/reported wobble.
|
|
Manufacturer Narrative
|
H3: analysis results were not available as of the date of this report. a follow-up report will be submitted when analysis is complete.H6: additional information suggest that fdm:4114, fdr:3221 and fdc:67 no longer apply to this event.The fdp was updated to e1603.Medtronic is submitting this report to comply with fda reporting regulations under 21 cfr parts 4 and 803.This report is based upon information obtained by medtronic, which the company may not have been able to fully investigate or verify prior to the date the report was required by the fda.Medtronic has made reasonable efforts to obtain more complete information and has provided as much relevant information as is available to the company as of the submission date of this report.This report does not constitute an admission or a conclusion by fda, medtronic, or its employees that the device, medtronic, or its employee caused or contributed to the event described in the report.In particular, this report does not constitute an admission by anyone that the product described in this report has any ¿defects¿ or has ¿malfunctioned¿.These words are included in the fda 3500a form and are fixed items for selection created by the fda to categorize the type of event solely for the purpose of regulatory reporting.Medtronic objects to the use of these words and others like them because of the lack of definition and the connotations implied by these terms.This statement should be included with any information or report disclosed to the public under the freedom of information act.Any required fields that are unpopulated are blank because the information is currently unknown or unavailable.A good faith effort will be made to obtain the applicable information relevant to the report.If information is provided in the future, a supplemental report will be issued.
|
|
Manufacturer Narrative
|
H3: analysis found that visually, there was no damage to the opened bur.The returned sample was placed into the handpiece and ran at 1000 rpm [the console minimum rpm is 1000]; there was no ¿noticeable¿ wobble with an unaided eye.When viewed under magnification, there was no visible damage to the green teflon bushing/sleeve.The bur run at 16,000 rpm and cut saw bone with no issues.There is no geometric dimensioning and tolerancing on the applicable drawings that control the reported wobble [i.E., runout, concentricity, true-position].H6: the fdm 4114 and fdr 3221 are no longer applicable.Medtronic is submitting this report to comply with fda reporting regulations under 21 cfr parts 4 and 803.This report is based upon information obtained by medtronic, which the company may not have been able to fully investigate or verify prior to the date the report was required by the fda.Medtronic has made reasonable efforts to obtain more complete information and has provided as much relevant information as is available to the company as of the submission date of this report.This report does not constitute an admission or a conclusion by fda, medtronic, or its employees that the device, medtronic, or its employee caused or contributed to the event described in the report.In particular, this report does not constitute an admission by anyone that the product described in this report has any ¿defects¿ or has ¿malfunctioned¿.These words are included in the fda 3500a form and are fixed items for selection created by the fda to categorize the type of event solely for the purpose of regulatory reporting.Medtronic objects to the use of these words and others like them because of the lack of definition and the connotations implied by these terms.This statement should be included with any information or report disclosed to the public under the freedom of information act.Any required fields that are unpopulated are blank because the information is currently unknown or unavailable.A good faith effort will be made to obtain the applicable information relevant to the report.If information is provided in the future, a supplemental report will be issued.
|
|
Search Alerts/Recalls
|
|
|