Model Number 405LS |
Device Problems
Melted (1385); Smoking (1585); Environmental Particulates (2930)
|
Patient Problem
No Clinical Signs, Symptoms or Conditions (4582)
|
Event Date 12/11/2023 |
Event Type
malfunction
|
Event Description
|
Customer reported "the instrument started smoking during use." pictures were provided confirming that a part inside the instrument had burned and melted.The lab technician immediately turned the power off and the instrument stopped smoking.Field service engineer (fse) was on site to evaluate the damage noting that the debris/ smoke particles are all over the instrument.The top cover is also partially burnt.Additionally, fse assessed the lab environment and recommended in house repair due to the extent of the damage.The instrument will be shipped back to the manufacturing site for further investigation.Diagnostics were not altered.There was no direct or indirect patient harm or user harm reported.The investigation is ongoing, and a supplemental report will be provided when new pertinent information is received.
|
|
Manufacturer Narrative
|
No erroneous staining result was reported by the customer in connection with this incident.No patient or user harm was indicated.A1-a6: not applicable.No patient involvement.
|
|
Manufacturer Narrative
|
This follow-up report is being submitted to relay additional information.The following sections were updated: b4, b5, d9, g3, g6, h2, h3, h6, h7, h11.
|
|
Event Description
|
Customer reported "the instrument started smoking during use." pictures were provided confirming that a part inside the instrument had burned and melted.The lab technician immediately turned the power off and the instrument stopped smoking.Field service engineer (fse) was on site to evaluate the damage noting that the debris/ smoke particles are all over the instrument.The top cover is also partially burnt.Additionally, fse assessed the lab environment and recommended in house repair due to the extent of the damage.Diagnostics were not altered.There was no direct or indirect patient harm or user harm reported.The instrument was returned for in-house repair.Vacuum relay on main printed circuit board (pcb) was found to be burnt.The unit was cleaned, and main pcb was replaced.1170204 1.47 software downloaded.The instrument has been calibrated and tested and is fully operational and available for use.The instrument is ready to be shipped back to the customer site.The investigation to determine root cause is ongoing, and a supplemental report will be provided when new pertinent information is received.
|
|
Manufacturer Narrative
|
This follow-up report is being submitted to relay additional information.Investigation conclusion: damage that matched the failures that occurred to the customer ssrs (relays) could not be reproduced.Ssrs were damaged, however the damage could only be produced at a minimum by shorting the pump fuse and seizing the pump (a double fault situation that would involve the user to knowingly alter the fusing of the system).The ssr failure does not appear to be a flaw in the product's design or usage.The ratings for the fuses used in the products are approximately 50% of the max rating recommended by the ssr manufacturer.Meaning the fuses are properly sized for use with the ssr.The results of the conducted tests showed that the product is adequately fused.All reasonable user-based fault conditions regarding the use of the waste system and pump failure modes were tested.No currents could be produced that would damage the ssr that wouldn't blow the fuse before damage could occur.The results of the conducted tests showed that the ssr could only be damaged by shorting the pump fuse and seizing the pump (a double fault situation that would involve the user to knowing alter the fusing of the system).It is a possibility that there is an issue with the customer's power system or perhaps damage due to a lightning strike.The product has met all of its compliance requirements for electrical fast transients, for surge immunity and user safety.Component failure.It may be possible that the ssr did not meet its specification over long term use.However, there have not been enough field failures to warrant further investigation of the issue.The customer is using an unapproved 0.2um inline vacuum filter.However, the impact of using the filter over the approved 1.0um filter is negligible in regards to this issue.The root cause could not be determined as the issue could not be reproduced.
|
|
Event Description
|
Customer reported "the instrument started smoking during use." pictures were provided confirming that a part inside the instrument had burned and melted.The lab technician immediately turned the power off and the instrument stopped smoking.Field service engineer (fse) was on site to evaluate the damage noting that the debris/ smoke particles are all over the instrument.The top cover is also partially burnt.Additionally, fse assessed the lab environment and recommended in house repair due to the extent of the damage.Diagnostics were not altered.There was no direct or indirect patient harm or user harm reported.The instrument was returned for in-house repair.Vacuum relay on main printed circuit board (pcb) was found to be burnt.The unit was cleaned, and main pcb was replaced.1170204 1.47 software downloaded.The instrument has been calibrated and tested and is fully operational and available for use.The instrument is ready to be shipped back to the customer site.
|
|
Search Alerts/Recalls
|