MAUDE Adverse Event Report: DEPUY MITEK LLC US FULL RADIUS 4.0MM 5PK; ARTHROSCOPIC SHAVER SYSTEM BLADE, SINGLE-USE

Model Number 283409

Device Problems Break (1069); Entrapment of Device (1212)

Patient Problems Foreign Body In Patient (2687); Not Applicable (3189)

Event Date 01/01/2020

Event Type  Injury  

Manufacturer Narrative

(b)(4).If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.To date the device has not been returned.If the device or further details are received at a later date a supplemental medwatch will be sent.Udi:(b)(4).The expiration date is unknown at this time.

Event Description

It was reported by affiliate via complaint submission tool as follows: again metal abrasion during knee arthroscopy.Lot: m2002035.Another device was used for surgery completion.There was surgical delay of 5 minutes.Fragments were generated, bigger parts still in the joint.The device is available for evaluation.

Manufacturer Narrative

Product complaint # (b)(4).This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.The actual device has been returned and is currently pending evaluation.Once reliability engineering evaluates the device, a supplemental medwatch report will be sent accordingly.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Udi:(b)(4).Incomplete the expiration date is unknown at this time.

Manufacturer Narrative

This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.D4, h4: the expiration date and manufacture date were reported as unknown on the initial report; and have been updated accordingly.Udi: (b)(4).

Manufacturer Narrative

This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Investigation summary: according to the information provided, it was reported metal abrasion during knee arthroscopy.The device was received and evaluated in juarez lab.It was observed that the inner shaft and the sleeve have friction marks right at the distal end.The picture provided by the customer showed metal shavings.From further investigation, this type of issue and part number was tested by the r&d team which determined the root cause and the potential ways to reduce the shedding.The investigation was divided into three stages, complaint blade inspection, spring force testing, o-ring testing.Since there were signs of wear and discoloration detected on the blades, the team decided to randomly select complaint blades to be inspected for out of specification tolerances.A doe (design of experiment) was constructed to test the three factors to see which have the largest effect on shedding.A tolerance analysis was conducted on the handpiece with blade assembly to find the maximum and minimum values for the gap where an acceptable amount of shedding is allowed.The test was conducted following the shed test method using eight blades alternating the following parameters: material type, speed, and spring force.In conclusion, the results show that the factor direction is above the specification, therefore it has the largest effect on shaver shedding of the three factors.Although factor of spring force is below the mark it was investigated since it is a factor that can be controlled while direction is based on surgeon discretion.The results conclude that the material does not have a significant effect on the shedding and that a higher amount of shedding occurs when the spring force is increased, and the shaver blade is run at higher speeds (=6,000 rpm).Also, a sample was ran for 30 seconds, sample two was ran for 60 seconds, and sample three was ran for 60 seconds.The test results concluded that if there is a significant amount of shedding it will occur in the first 30 seconds and not gradually over time.In addition, after discovering that some handpieces were missing the o-ring in the front of the handpiece, a test was conducted to determine how this could affect shedding.This complaint can be confirmed.As seen in the results shedding can be reproduced, but with the o-ring present and proper spring force maintained, the amount of shedding is significantly decreased.A manufacturing record evaluation was performed for the finished device m2002035 number, and no non-conformances were identified.Based on the investigation potential ways to reduce shedding is to ensure all handpieces are properly serviced and maintained to ensure the presence of the o-ring.During the servicing make sure tissue seal spring is properly placed and that no debris is caught on or under the tissue seal spring, which could cause an increase in the spring force.Continue to monitor and inspect the handpiece usage in the region and verify that the decontamination and cleaning processes are following the proper ifu.Another potential way to reduce shedding is to run the blades at a lower speed and in oscillation direction as shown in the test results.As this complaint rate falls within the expected occurrence rate per the dfmea, no further risk reduction actions are required.At this point in time, no corrective action is required, and no further action is warranted.However, depuy synthes mitek will continue to track any related complaints within this device family as a means of monitoring the extent with which this complaint is observed in the field.

• Brand Name: FULL RADIUS 4.0MM 5PK
• Type of Device: ARTHROSCOPIC SHAVER SYSTEM BLADE, SINGLE-USE
• Manufacturer (Section D): DEPUY MITEK LLC US; 325 paramount drive; raynham MA 02767
• MDR Report Key: 10760015
• MDR Text Key: 213888410
• Report Number: 1221934-2020-03247
• Device Sequence Number: 1
• Product Code: HRX
• UDI-Device Identifier: 10886705022014
• UDI-Public: 10886705022014
• Combination Product (y/n): N
• PMA/PMN Number: K041824
• Number of Events Reported: 1
• Summary Report (Y/N): N
• Report Source: Manufacturer
• Source Type: company representative,foreig
• Type of Report: Initial,Followup,Followup,Followup
• Report Date: 10/15/2020

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Date FDA Received: 10/30/2020
• Is this an Adverse Event Report?: Yes
• Is this a Product Problem Report?: Yes
• Device Operator: Health Professional
• Device Model Number: 283409
• Device Catalogue Number: 283409
• Device Lot Number: M2002035
• Was Device Available for Evaluation?: Device Returned to Manufacturer
• Date Returned to Manufacturer: 12/07/2020
• Date Manufacturer Received: 01/11/2021
• Patient Sequence Number: 1