MAUDE Adverse Event Report: STRYKER GMBH BASEPLATE; PROSTHESIS, SHOULDER, SEMI-CONSTRAINED, METAL/POLYMER CEMENTED

Catalog Number	5572-2800
Medical Device Problem Codes	Material Deformation (2976); Osseointegration Problem (3003)
Health Effect - Clinical Codes	Failure of Implant (1924); Osteolysis (2377); Inadequate Osseointegration (2646); Foreign Body In Patient (2687)
Date of Event	10/12/2023
Type of Reportable Event	Serious Injury
Event or Problem Description
The surgeon scheduled a revision surgery with a stryker representative.During the surgery, it was found that the baseplate/screw/glenosphere construct was loose, with two of the four screws not contained within the construct.The glenoid baseplate/glenosphere/screws and the cup/poly construct were removed.A 40mm humeral head was attached to the existing humeral stem.The indication for the primary procedure was a fracture.The revision surgery was successful.
Additional Manufacturer Narrative
Analysis results are not available at the time of this report.A follow-up report will be sent when the analysis is complete.
Additional Manufacturer Narrative
Please note the corrections regarding d1 product long description, g1: the reported event was confirmed based on the inspection performed.The received baseplate was stuck in the glenosphere, therefore, the lot number could not be identified and was not communicated.Since no major sign of product or material issue was observed (see product inspection), a deeper investigation of the lot was not deemed necessary.The device inspection revealed the following: the received baseplate was stuck in the glenosphere.Wear and small deformation could be observed on the peripheral screw holes of the baseplate, which led to two screws coming out.This caused the loosening of the baseplate.No other major damage or sign of material issue could be detected.Two x-rays showing the loosen implant were sent for investigation and were analysed by a medical expert, who stated: "the x-rays show loosening of the glenoid construct, and one screw that came out of the baseplate.It is not easy to see, but on the x-ray, 3 peripheral screws can be recognized, one of them partially hiding behind the central screw in the ap-projection.There is also metal debris in the axilary part of the joint capsule, little metal flakes can be seen near the free ¿floating¿ screw.This can only happen when the base plate loosens, the hole of the peripheral screws wears out so much, it can escape the baseplate with the glenopshere still in place.The root cause is loosening of the baseplate, osteolysis around the screw, with subsequent wear of its hole in the baseplate of the peripheral screw leading to the migration of the screw." based on investigation, the root cause was attributed to a patient condition related issue.As stated by the medical expert, after inspection of the x-rays, it could be concluded that osteolysis around the screws led to wear and loosening of the baseplate.No corrective actions are required at this time.A review of the labeling did not indicate any abnormalities.If more information is provided, the case will be reassessed.
Event or Problem Description
The surgeon scheduled a revision surgery with a stryker representative.During the surgery, it was found that the baseplate/screw/glenosphere construct was loose, with two of the four screws not contained within the construct.The glenoid baseplate/glenosphere/screws and the cup/poly construct were removed.A 40mm humeral head was attached to the existing humeral stem.The indication for the primary procedure was a fracture.The revision surgery was successful.

• Brand Name: BASEPLATE
• Common Device Name: PROSTHESIS, SHOULDER, SEMI-CONSTRAINED, METAL/POLYMER CEMENTED
• Manufacturer (Section D): STRYKER GMBH; bohnackerweg 1; postfach; selzach 2545 ; SZ 2545
• Manufacturer (Section G): STRYKER TRAUMA KIEL; prof. kuentscher-strasse 1-5; schoenkirchen/kiel D-242 32; GM D-24232
• Manufacturer Contact: anna jusinski ; 325 corporate drive; mahwah, NJ 07430 ; 2018315000
• MDR Report Key: 18096712
• Report Number: 0009610622-2023-00398
• Device Sequence Number: 14994110
• Product Code: KWS
• UDI-Device Identifier: 07613327098709
• UDI-Public: 07613327098709
• Combination Product (Y/N): N
• Initial Reporter State: VA
• Initial Reporter Country: US
• Number of Events Summarized: 1
• Summary Report (Y/N): N
• Device Implanted Year: 2023
• Reporter Type: Manufacturer
• Report Source: Health Professional
• Initial Reporter Occupation: Physician
• Type of Report: Initial,Followup
• Report Date (Section B): 02/02/2024

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Is this an Adverse Event Report?: Yes
• Is this a Product Problem Report?: No
• Operator of Device: Lay User/Patient
• Device Catalogue Number: 5572-2800
• Device Lot Number: UNKNOWN
• Was Device Available for Evaluation?: Device Returned to Manufacturer
• Date Returned to Manufacturer: 10/27/2023
• Is the Reporter a Health Professional?: Yes
• Type of Report(Section G): Initial
• Initial Date Received by Manufacturer: 10/12/2023
• Supplement Date Received by Manufacturer: 01/11/2024
• Initial Report FDA Received Date: 11/08/2023
• Supplement Report FDA Received Date: 02/02/2024
• Was Device Evaluated by Manufacturer? (Y/N): No
• Is the Device Labeled for Single Use? (Y/N): Yes
• Is This a Single-Use Device that was Reprocessed and Reused on a Patient? (Y/N): No
• Usage of Device: Initial
• Patient Sequence Number: 1
• Outcome Attributed to Adverse Event: Required Intervention
• Patient Age: 79 YR
• Patient Sex: Female