MAUDE Adverse Event Report: MEDOS INTERNATIONAL SARL CORACOID TOP HAT DRILL; BIT, DRILL

Catalog Number	288202
Medical Device Problem Code	Degraded (1153)
Health Effect - Clinical Code	No Clinical Signs, Symptoms or Conditions (4582)
Date of Event	11/05/2024
Type of Reportable Event	Malfunction
Additional Manufacturer Narrative
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Device was used for treatment, not diagnosis.H11 additional narrative: e3: reporter is a j&j sales representative.H4: the device manufacture date is currently unavailable.As of this date, the device has not been returned for evaluation; therefore, the reported condition cannot be confirmed and/or duplicated.
Event or Problem Description
It was reported from australia that two sets of devices had blunt instruments.It was reported that the two coracoid top hat drill devices, and two sharp curved osteotome devices were blunt.It was not reported if the event occurred during a surgical procedure.There were no reports of injuries, medical intervention, or prolonged hospitalization.All available information has been disclosed.This is report 3 of 4 for the same event in (b)(4).
Additional Manufacturer Narrative
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Device was used for treatment, not diagnosis.H11 additional narrative: d4: the lot number was reported as unknown on the initial report; and has been updated accordingly.Therefore, the udi has been updated accordingly.
Additional Manufacturer Narrative
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Device was used for treatment, not diagnosis.H11 additional narrative: h4: the device manufacture date was reported as unknown on the initial report.Please note that the date of manufacture has been updated accordingly.
Additional Manufacturer Narrative
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Device was used for treatment, not diagnosis.Investigation summary: the complaint device was discarded by the customer, therefore not returned to j&j medtech orthopaedics and unavailable for a physical evaluation.A manufacturing record evaluation was performed for the finished device lot number, and no non-conformance was identified.Based on the current available information, we cannot determine a root cause for the reported failure.If additional information is received in the future, we will reopen the complaint and perform the investigation as appropriate.It has been determined that no corrective and/or preventative action is proposed and there is no indication that a design or manufacturing issue has caused the reported complaint condition.As part of j&j medtech orthopaedics quality process, all devices are manufactured, inspected, and released to approved specifications.Additional monitoring for any potential safety signals will be conducted through complaint trending and other post-market safety surveillance activities.
Additional Manufacturer Narrative
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Device was used for treatment, not diagnosis.H11 additional narrative: d9, h3, h6: the actual device has been returned and is currently pending evaluation.Once reliability engineering evaluates the device, a supplemental medwatch report will be sent accordingly.
Additional Manufacturer Narrative
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Device was used for treatment, not diagnosis.H11 additional narrative: investigation summary: the product was returned to j&j medtech orthopaedics for evaluation.Visual inspection of the returned device found that the device comes in used condition as expected in reusable devices.The drill tip is dull.The device's shaft has no structural anomalies.The device was manufactured in 2017 which is 7 years old.A functional test was unable to be performed due to the post-manufacturing damage.The observed condition was identified as an end of life indicator; damage consistent with repeated use and servicing.The lifecycle requirements of the device are event related and depend on the use and inspection of the device in clinical practice.As the device can be damaged on the first or 100th use, the device must be properly inspected prior to each surgical use.Refer to the device/country specific ifu for information related to end of life, reprocessing instructions, and inspection procedures.The overall complaint was confirmed as the observed condition of the coracoid top hat drill would have contributed to the complained device issue.Based on the investigation findings, the potential cause is traced to end of life, and it has been determined that no corrective and/or preventative action is required.There is no indication that a design or manufacturing issue has caused the reported complaint condition.As part of j&j medtech orthopaedics quality process, all devices are manufactured, inspected, and released to approved specifications.Additional monitoring for any potential safety signals will be conducted through complaint trending and other post-market safety surveillance activities.Device history lot: a manufacturing record evaluation was performed for the finished device lot number, and no non-conformance was identified.
Additional Manufacturer Narrative
This report is being submitted in pursuant to the provisions of 21 cfr, part 803.This report may be based on information which has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by mitek or its employees that the report constitutes an admission that the device, mitek, or its employees caused or contributed to the potential event described in this report.If information is obtained that was not available for the initial medwatch, a follow-up medwatch will be filed as appropriate.Device was used for treatment, not diagnosis.H11 additional narrative: additional information b5, h11: please note that two additional products have been added to the complaint.The investigation has been updated with additional information.Investigation summary: the product was returned to j&j medtech orthopaedics for evaluation.Visual inspection of the returned device found that the device comes in used condition as expected in reusable devices.The drill tip is dull.The device's shaft has no structural anomalies.The device was manufactured in 2017 which is 7 years old.A functional test was unable to be performed due to the post-manufacturing damage.The observed condition was identified as an end of life indicator; damage consistent with repeated use and servicing.The lifecycle requirements of the device are event related and depend on the use and inspection of the device in clinical practice.As the device can be damaged on the first or 100th use, the device must be properly inspected prior to each surgical use.Refer to the device/country specific instructions for use (ifu) for information related to end of life, reprocessing instructions, and inspection procedures.The overall complaint was confirmed as the observed condition of the coracoid top hat drill would have contributed to the complained device issue.Based on the investigation findings, the potential cause is traced to end of life, and it has been determined that no corrective and/or preventative action is required.There is no indication that a design or manufacturing issue has caused the reported complaint condition.As part of j&j medtech orthopaedics quality process, all devices are manufactured, inspected, and released to approved specifications.Additional monitoring for any potential safety signals will be conducted through complaint trending and other post-market safety surveillance activities.Device history lot: a manufacturing record evaluation was performed for the finished device lot number, and no non-conformance was identified.
Event or Problem Description
Event description update: it was reported from australia that two sets of devices had blunt instruments.It was reported that the two coracoid top hat drill devices, two sharp curved osteotome devices, a combo screwdriver, and a coracoid offset pin were blunt.It was not reported if the event occurred during a surgical procedure.There were no reports of injuries, medical intervention, or prolonged hospitalization.All available information has been disclosed.This is report 3 of 6 for the same event in (b)(4).

• Brand Name: CORACOID TOP HAT DRILL
• Common Device Name: BIT, DRILL
• Manufacturer (Section D): MEDOS INTERNATIONAL SARL; chemin-blanc 38; le locle 02400 ; SZ 02400
• Manufacturer (Section G): MEDOS INTERNATIONAL SARL; chemin-blanc 38; le locle CH-24 00; SZ CH-2400
• Manufacturer Contact: kate karberg ; 325 paramount drive; raynham, MA 02767 ; 3035526892
• MDR Report Key: 20677337
• Report Number: 1221934-2024-04080
• Device Sequence Number: 8949780
• Product Code: HTW
• UDI-Device Identifier: 10886705026807
• UDI-Public: (01)10886705026807(10)17K01
• Combination Product (Y/N): N
• Initial Reporter Country: AS
• PMA/510(K) Number: EXEMPT
• Number of Events Summarized: 1
• Summary Report (Y/N): N
• Serviced by Third Party (Y/N): Unknown
• Reporter Type: Manufacturer
• Report Source: Foreign,User Facility,Company Representative
• Initial Reporter Occupation: Other
• Type of Report: Initial,Followup,Followup,Followup,Followup

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Is this an Adverse Event Report?: No
• Is this a Product Problem Report?: Yes
• Operator of Device: Health Professional
• Device Catalogue Number: 288202
• Device Lot Number: 17K01
• Was Device Available for Evaluation?: Device Returned to Manufacturer
• Is the Reporter a Health Professional?: No
• Type of Report(Section G): Thirty-Day
• Initial Date Received by Manufacturer: 11/05/2024
• Supplement Date Received by Manufacturer: 11/13/2024; 11/26/2024; 11/29/2024; 01/13/2025; 01/20/2025; 01/20/2025
• Initial Report FDA Received Date: 11/13/2024
• Supplement Report FDA Received Date: 11/18/2024; 11/26/2024; 12/03/2024; 01/15/2025; 01/21/2025; 01/23/2025
• Was Device Evaluated by Manufacturer? (Y/N): Yes
• Date Device Manufactured: 08/02/2017
• Is the Device Labeled for Single Use? (Y/N): No
• Is This a Single-Use Device that was Reprocessed and Reused on a Patient? (Y/N): No
• Usage of Device: Unknown
• Patient Sequence Number: 1
• Patient Sex: Unknown