MAUDE Adverse Event Report: C.R. BARD INC. (COVINGTON) -1018233 BARDEX® LUBRI-SIL® I.C. ALL-SILICONE TEMP SENSING FOLEY CATHETER

Catalog Number	119314M
Medical Device Problem Code	Material Puncture/Hole (1504)
Health Effect - Clinical Code	No Clinical Signs, Symptoms or Conditions (4582)
Date of Event	02/04/2025
Type of Reportable Event	Malfunction
Event or Problem Description
It was reported that this was the item for flint.They were getting safety firsts every day about this defective kit.There was small hole at top of temp catheter, balloon deflating, urine flowing out after moving the tubing, foley catheter not draining properly with no kinks in it.
Additional Manufacturer Narrative
The investigation is still in progress.Once the investigation is complete a supplemental report will be filed.Udi format updated with available product information per gudid.H11: section a through f - the information provided by bd represents all the known information at this time.Despite good faith efforts to obtain additional information, the complainant/reporter was unable or unwilling to provide any further patient, product, or procedural details to bd.
Additional Manufacturer Narrative
The reported event was inconclusive because this investigation did not result in any additional findings and no sample was available for evaluation.No actions can be taken at this time since a root cause was not identified.A dhr could not be performed since no lot number was provided.The instructions for use were found adequate and state the following: special instructions: the position of the wire of the temperature sensing foley catheter has an important effect on the amount of heating that may develop during an mri examination.Accordingly, the temperature sensing foley catheter must be positioned in a straight configuration down the center of the patient table (i.E., down the center of the mr system without any loop) without contacting the patient in order to ensure patient safety.This product should never connected to the temperature monitor or connected to a cable during an mri procedure.Failure to follow this guideline may result in serious injury to the patient.Refer to instructions for use! it is important to closely follow these specific conditions that have been determined to permit the examination to be conducted safely.Any deviation may result in a serious injury to the patient.Additional safety instructions include the following: 1.Remove all electrically conductive material from the bore of the mr system that is not required for the mri examination (i.E., unused surface coils, cables, etc.).2.Keep electrically conductive material that must remain in the bore of the mr system from directly contacting the patient by placing insulating material such as foam rubber padding between the conductive material and the patient.3.Position the temperature sensing foley catheter in a straight configuration down the center of the patient table to prevent cross points and conductive coils or loops.4.The wire and connector of the temperature sensing foley catheter should not be in direct contact with the patient during the mri examination.Position the temperature sensing foley catheter appropriately and add insulating material such as foam rubber padding, accordingly.Udi format updated with available product information per gudid.H11: section a through f: the information provided by bd represents all the known information at this time.Despite good faith efforts to obtain additional information, the complainant / reporter was unable or unwilling to provide any further patient, product, or procedural details to bd.
Event or Problem Description
It was reported that this was the item for flint.They were getting safety firsts every day about this defective kit.There was small hole at top of temp catheter, balloon deflating, urine flowing out after moving the tubing, foley catheter not draining properly with no kinks in it.

• Brand Name: BARDEX® LUBRI-SIL® I.C. ALL-SILICONE TEMP SENSING FOLEY CATHETER
• Common Device Name: FOLEY CATHETER
• Manufacturer (Section D): C.R. BARD INC. (COVINGTON) -1018233; 8195 industrial blvd; covington GA 30014
• Manufacturer (Section G): C.R. BARD INC. (COVINGTON) -1018233; 8195 industrial blvd; covington GA 30014
• Manufacturer Contact: xeeroy rada ; 8195 industrial blvd; covington 30014 ; 7707846100
• MDR Report Key: 21424085
• Report Number: 1018233-2025-01117
• Device Sequence Number: 7913848
• Product Code: MJC
• UDI-Device Identifier: 00801741039904
• UDI-Public: (01)00801741039904
• Combination Product (Y/N): Y
• Initial Reporter State: MI
• Initial Reporter Country: US
• PMA/510(K) Number: K070582
• Number of Events Summarized: 1
• Summary Report (Y/N): N
• Reporter Type: Manufacturer
• Report Source: Other,Health Professional,User Facility,Company Representative
• Initial Reporter Occupation: Physician
• Type of Report: Initial,Followup
• Report Date (Section B): 05/29/2025

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Is this an Adverse Event Report?: No
• Is this a Product Problem Report?: Yes
• Operator of Device: Health Professional
• Device Catalogue Number: 119314M
• Was Device Available for Evaluation?: No
• Is the Reporter a Health Professional?: Yes
• Type of Report(Section G): Thirty-Day
• Initial Date Received by Manufacturer: 02/04/2025
• Supplement Date Received by Manufacturer: 05/29/2025
• Initial Report FDA Received Date: 02/20/2025
• Supplement Report FDA Received Date: 06/05/2025
• Was Device Evaluated by Manufacturer? (Y/N): No
• Is the Device Labeled for Single Use? (Y/N): Yes
• Is This a Single-Use Device that was Reprocessed and Reused on a Patient? (Y/N): No
• Usage of Device: Initial
• Patient Sequence Number: 1
• Outcome Attributed to Adverse Event: Other
• Patient Sex: Unknown