MAUDE Adverse Event Report: MENTOR TEXAS MENTOR SMOOTH ROUND MODERATE PROFILE; PROSTHESIS, BREAST, INFLATABLE, INTERNAL, SALINE

Catalog Number	3501697
Medical Device Problem Code	Material Rupture (1546)
Health Effect - Clinical Code	Deformity/ Disfigurement (2360)
Date of Event	10/13/2025
Type of Reportable Event	Serious Injury
Additional Manufacturer Narrative
Since the device has not been returned for analysis, no product failure analysis can be conducted, and no determination of possible contributing factors can be made.As such, the investigation will be closed.If the complaint device is received in the future, the investigation will be reopened and conducted as appropriate.A manufacturing record evaluation (mre) was performed, and no anomalies were found related to this complaint.In addition, the mre verifies that the device was manufactured in accordance with documented specification and procedures.Reason for device explant and/or reoperation: deflation.Mentor is submitting this report pursuant to the provisions of 21 cfr, part 803.This report may be based on information which mentor has not been able to investigate or verify prior to the required reporting date.This report does not reflect a conclusion by fda, mentor, or its employees that the report constitutes an admission that the device, mentor, or its employees caused or contributed to the potential event described in this report.If certain information is unknown, not available or does not apply, the section/field of the form is left blank.Manufacturer¿s reference number: (b)(4).
Event or Problem Description
It was reported that a patient underwent a breast augmentation revision surgery with implantation of a 700cc mentor smooth round moderate profile saline breast implant prosthesis.Post-operatively, the patient was diagnosed with a deflated left implant during a physical exam.As a result, the patient underwent implant removal on (b)(6) 2025.
Additional Manufacturer Narrative
On november 21, 2025, the mentor analysis lab received the suspect medical device for evaluation.On november 27, 2025, mentor completed an evaluation on the returned device.Device evaluation: mentor then conducted a visual inspection, microscopic examination, and thickness measurement of the device.Visual analysis of the returned device revealed that the breast implant was found to have a tear on the anterior view, near the valve system, measuring approximately 7.0 cm.Microscopic examination was performed, and the cause of the deflation could not be identified.Therefore, a thickness measurement was conducted on the shell at the tear, and the thickness was within manufacturing specifications.Although no conclusion could be reached on the cause of the reported event, the instructions for use contain the following caution: according to the product insert data sheet, the valve system can be damaged by improper use of the fill-tube stylet.Care should be taken that the stylet enters the valve smoothly.Use the thumb and forefinger to stabilize/support the valve seat and gently push the stylet tip into the valve opening.Overstressing the valve material may result in punctures or tears and subsequent deflation may occur.Use only the fill tube stylet provided with this product.Take care not to puncture the diaphragm valve or the shell with the stylet tip.Care must also be taken when the fill tube stylet is removed to prevent damage to the valve assembly.Manufacturer¿s reference number: (b)(4).

• Brand Name: MENTOR SMOOTH ROUND MODERATE PROFILE
• Common Device Name: PROSTHESIS, BREAST, INFLATABLE, INTERNAL, SALINE
• Manufacturer (Section D): MENTOR TEXAS; 3041 skyway circle north; irving TX 75038
• Manufacturer (Section G): MENTOR TEXAS; 3041 skyway circle north; irving TX 75038
• Manufacturer Contact: henry boden ; 3041 skyway circle north; irving, TX 75038 ; 9497882078
• MDR Report Key: 23456464
• Report Number: 1645337-2025-12216
• Device Sequence Number: 12780901
• Product Code: FWM
• UDI-Device Identifier: 00081317001331
• UDI-Public: (01)00081317001331(17)270629(10)9926968
• Combination Product (Y/N): N
• Initial Reporter Country: US
• PMA/510(K) Number: P990075
• Number of Events Summarized: 1
• Summary Report (Y/N): N
• Device Implanted Year: 2025
• Device Explanted Year: 2025
• Serviced by Third Party (Y/N): Unknown
• Reporter Type: Manufacturer
• Report Source: Health Professional
• Initial Reporter Occupation: Other
• Type of Report: Initial,Followup

1 Device was Involved in the Event

1 Patient was Involved in the Event

• Is this an Adverse Event Report?: Yes
• Is this a Product Problem Report?: Yes
• Operator of Device: Health Professional
• Device Catalogue Number: 3501697
• Device Lot Number: 9926968
• Was Device Available for Evaluation?: Device Returned to Manufacturer
• Is the Reporter a Health Professional?: No
• Type of Report(Section G): Follow-Up
• Initial Date Received by Manufacturer: 10/13/2025
• Supplement Date Received by Manufacturer: 11/21/2025
• Initial Report FDA Received Date: 11/03/2025
• Supplement Report FDA Received Date: 12/02/2025
• Was Device Evaluated by Manufacturer? (Y/N): Yes
• Date Device Manufactured: 07/17/2023
• Is the Device Labeled for Single Use? (Y/N): Yes
• Is This a Single-Use Device that was Reprocessed and Reused on a Patient? (Y/N): No
• Usage of Device: Initial
• Patient Sequence Number: 1
• Outcome Attributed to Adverse Event: Required Intervention
• Patient Age: 39 YR
• Patient Sex: Female